Clean air is vital to all combustion processes. The prime function of an inlet filter system is to protect the gas turbine from pollutants in the air, as particles entering can cause costly damages like erosion, corrosion and fouling. Erosion is a permanent degradation, mainly caused by coarse particles,

while corrosion is caused by salt in combination with sulphur, and high temperatures. Smaller particles cause fouling of turbine blades, and thus affecting performance negatively. A secondary effect is an increase in temperatures, as heat transfer effectiveness is reduced, and ultimately the life of the hot section. Effective capture of particulate and airborne salt is therefore of vital importance for long and efficient operation. If not removed by the inlet system, particles will force operators to more frequently water wash the compressor, either by unnecessary on-line washing or during costly shut downs.

It is also important to understand the complexity of differentiating air filters. Most air filters remain in a system for months or even years. During this time, the filter will experience several environmental variations like changes in temperature, humidity, airflow velocity and particle load. To prevent this, and make sure our filters withstand the severe real life conditions once in operation

進氣過濾系統的主要功能是保護燃氣輪機免受空氣中的污染,如顆粒進入會造成大的造價損害,如腐蝕或污垢。腐蝕是一種長久性的退化,主要是由大顆粒引起的,而腐蝕則是由鹽與硫的結合和高溫引起的。較小的顆粒會引起渦輪葉片的污垢,從而對渦輪的性能產生不利的影響。二次效應是溫度升高,傳熱效率降低,會導致熱壽命的延長。

因此,有效捕獲微粒和空氣中的鹽對于長期有效運作至關重要。如果不被入口移除系統中,粒子會迫使操作者更頻繁地用水沖洗壓縮機,要么通過不必要的在線清洗,要么在昂貴的停機期間。所以匹配空氣過濾器是很重要的。大多數空氣過濾器在一個系統中停留數月甚至幾年。在此期間,過濾器將經歷幾種環境變化,如溫度、濕度、氣流速度和顆粒負荷的變化。為了防止這一切,而且確保我們的過濾器一旦投入運行就能承受惡劣的現實條件;

以上空氣過濾器技術參數金科過濾器通過第三方機構認證公司進行測試并提供檢測報告。

These are general recommendations for gas turbine air inlet systems.

這些是燃氣輪機進氣系統的一般建議

Generally, the international common size (24“ × 24 "or 592 × 592mm) filter, and take this ruler as the modulus, change the filter to 2 × 2、3 × 2、3 × Third order matrix arrangement; The filter technical parameters are generally divided into the following three types, which can be matched and designed according to the different needs of customers.

通常以國際通用尺寸(24"×24" 即592×592mm)過濾器,并以此尺?為模數,將過濾器以2×2、3×2、3×3等矩陣排列;過濾器技術參數通常分為以下三種,具體可根據根據客?不同的需求來匹配設計。

一級初效過濾器:過濾等級G4,通風量3400CMH,初始風壓≤40Pa;容塵量1700g.

二級中效過濾器:過濾等級F8~F9,通風量3400CMH,初始風壓≤130Pa;容塵量900g.

三級高效過濾器:過濾等級H12~H13,通風量3400CMH,初始風壓≤250Pa;容塵量800g.

優勢:

可制作不同過濾效率等級,適用不同的客戶要求.

芯片采用美國設備全自動折疊以及國內先進設備全自動電腦控制系統進行噴膠成型.

材質:

外框:ABS塑料框、各種不銹鋼

濾料:高防水玻璃纖維濾紙.PTFE.納米材料等

分隔物:熱熔膠(環保無氣味)

密封膠:聚氨酯(環保無氣味)

密封墊:CR\EPDM